copied from http://www.sulit.com.ph/index.php/view+classifieds/id/1553209/Fire+Protection%2C+Rig+Cooling%2C+Gas+Mitigation%2C+Cooling+Tower+%26+Oil+Burner+Nozzles
FIRE PROTECTION NOZZLES | UL (Underwriter Laboratory) APPROVED | |
|  
HD SERIES |
Material - Brass with Bright Nickel Chrome, Aluminium Bronze Approvals - UL Listed HD BRASS SERIES NOZZLES ARE UL LISTED Open orifice design used in fire deluge system in offshore platforms, rigs, ships. Size 1/2" BSPT or NPT (Male) Full cone spray pattern K-factor: Metric - 22, 30, 35, 41, 51, 64, 79, 91 & 102 K-factor: US -1.54, 2.10, 2.45, 2.87, 3.57, 4.48, 5.53, 6.37 & 7.14 Spray angle - 65°,80°,90°,100°,110°,120° & 140° Each Nozzle body permanently marked with model number, batch number, spray angle, K-factor & UL mark RIG COOLING FM (Factory Mutual) APPROVED MODEL : RIGSPRAY 30 Flow 1500 to 2850 Lpm (400 to 750 gpm) Easy pattern change under flowing condition from straight stream to wide fog 120 degrees full cone. Field replaceable spinning teeth ring Excellent water stream used as water nozzle or non-aspirating foam nozzle Flow set at 6.9 bar (100 psi) can be changed from 5.6 to 12 bar (80 to 175 psi), if required 2.5" BSP swivel female inlet base Hard anodized Aluminium or corrosion resistant Bronze material. GAS MITIGATION NOZZLE MODEL : T48(170) Flow range 153 Lpm @0.5 Bar to 968 Lpm @ 20 Bar (41 to 256 Gpm) 120 degrees, 150 degrees or 170 degrees Full Cone Atomise Droplets range 650 microns to 2000 microns One piece construction, Non clog 1" NPT (M) or BSP(M) connection Copper Nickel C95600, Naval Brass C48400 for Sea Water Application. Corrosion resistant Silicon Al. Bronze. FOAM NOZZLES
| | LOW EXPANSION FOAM NOZZLES |
|  
| The RFV Low Expansion Foam Nozzles consist of a body and a deflector especially designed for an optimized foam distribution. The foam solution stream is fractioned and air is sucked in inside the brass body, and then distributed by the deflector with covering angles up to 95°. Foam expansion rate typically 1:7. Body Material : Brass, Impact Disc : AISI 304 stainless steel  |
|
| | MEDIUM EXPANSION FOAM NOZZLES |
| RHU 0075 RHU 0100 | The RH foam nozzles were designed to work on the Venturi principle. A stream of foam solution is sprayed at high speed against an outlet net, drawing into the body the air required and producing foam with an expansion ratio of about 1:20  |
|
| Monitor M 241 | WATER / FOAM MONITORS |
| 
HAND-LEVER CONTROLLED | - Stainless steel waterway
- 63 mm (2.5") waterway, Inlet flanged 65, 80 or 100 mm (2.5" 3" or 4") and outlet threaded to 2.5" BSP male
- Vertical and horizontal movement by handle and manual lock
- Bronze or Stainless steel swivel joint with double row of stainless steel ball bearing and grease fittings
- 360° continuous horizontal rotation and +90°, -45° vertical elevation
- Maximum operating pressure 12 bar (175 psi).
- Flow up to 2270 Lpm (600 gpm) friction loss less than 10 psi
|
|
|
|
| Monitor 433 | HAND-WHEEL / SELF-OSCILLATING |
| 
HAND-WHEEL - FM Approved | - Cast bronze construction
- Fully enclosed gear
- Liquid filled pressure gauge
- Double row of Stainless Steel ball bearing with grease fittings
- Maximum operating pressure 12 bar (175 psi)
- 115 mm waterway with 100 or 150 mm (4" or 6") flanged inlet and 4" BSP male threaded outlet
- 360° continuous horizontal rotation, +90°, -45° vertical elevation
- Red polyurethane finish
|
|
|
|
| | |
| | Inline Foam Inductor |
| 
| - Aluminium, Bronze or Stainless steel construction
- 50, 65, 80, 100 & 150 mm (2", 2.5", 3", 4" & 6") size with fix flow of 75 to 3500 lpm
- Working pressure 6.4 to 12 bar (93 to 175 psi)
- Maximum back pressure as 65%
- Each unit is calibrated and factory tested for flow, induction rate at maximum back pressure
|
|
|
|
| | Inline Balance Pressure Foam Proportioner |
| 
| - Bronze or Stainless steel material with SS / Brass trims
- 80, 100, 150 & 200 mm size (3", 4", 6" & 8") with flow ranging from 270 to 18500 lpm
- Working pressure 3.5 to 14 bar (50 to 200 psi)
|
|
|
|
| | |
| | Bladder Tank Proportioning Skid |
| 
| - Vertical or horizontal mounting
- 150 to 10,000 ltrs. (40 to 2642 gallon) capacity
- Tank made fabricated to ASME code
- Bladder made out of thermoplastic rubber
- Can be supplied with concentrate control valve
- Wide flow range
|
|
|
|
| | |
| | Positive Displacement Foam Proportioning Skid |
| | - Compact skid mounted unit with Foam Concentrate Pump, Ratio Controller, By-pass Valve, Relief Valve, Electricals etc.
- Offers wide range of flow from 270 to 18500 lpm (71 to 4887 gpm) without any need for manual adjustment
- Ready to hook up to the system
|
|
|
Cooling Tower Wash Spinning Nozzles | 
COOLING TOWER WASH SPINNING NOZZLES | The new SpinFree Nozzle produces a near perfect square pattern, which provides balanced water loading. These two features increase thermal performance in cooling towers and other cooling equipment by 10 - 12% by simply changing out the water nozzles. Round pattern nozzles produce an umbrella like pattern and are plagued with void areas. If you were to position these nozzles evenly over a square configuration, 22% of the area would be void of water because circles cannot mesh evenly. The SpinFree nozzle has four major design features that each will contribute significant value to the operations of cooling towers and other heat transfer equipment. - Square Spray Pattern
- The SpinFree nozzle produces a square water distribution pattern, which will increase thermal performance by 10% to 12%.
- Variable Flow Capabilities
- The SpinFree nozzle has variable flow capability with a 2 to 1 turn down ratio, allowing pumps to be > cycle off during cool climatic conditions or when loads demands are down.
- Operates Just 3" off the Surface
- The SpinFree nozzle operates only 3” above the fill media reducing structural height requirements in new tower construction. Also this feature reduces tower pump head by approximately (2) ft.
- Low Pressure Operation
- The SpinFree nozzle operates at a sweet spot of only (1) lb of pressure as compared to 2lbs or more for other nozzles.
|
| |
| 
| NOZZLE SPECIFICATIONS
Nozzles are provided ribbed sintered bronze filters on
sizes up through 1.35 GPH. Larger sizes are equipped
with 120 mesh strainers. Large Capacity (LC) nozzles
are supplied as “tips only”. All nozzle components are
fabricated entirely of a special high chrome, heat
resistant grade of stainless steel. Sintered filters are
made of bronze and are nominally rated for filtration
to 40 microns. Mesh screens are of Type 304 stainless
steel on brass support pieces.
|
| 
| STRAINERS & FILTERS Nozzle strainers are available in all configurations
and are supplied standard on flow rates of 1.50
and above. Bodies are brass, although stainless
steel bodies are available on special order.
Sintered bronze filters rated to 40 micr ons are
supplied on all nozzles of 1.35 & below.
All strainers and filters ar e made with
a 3/8"-40 UNS male thread to match the nozzle. |
| |
| 
| Spray Gun
Brass Body, 1/4” NPT Inlet, 1/4" NPT female outlet.
Rated Temperature 160deg.C, rated flow 35 l/min. Rated Pressure - 4 Bar, |
|
| 
| UMS0037E3 Delrin Gun;
UMS0038E3 Delrin Gun with 300mm P/P Lance Delrin body with stainless steel internals and Viton seals.
1/2" BSP Female inlet and outlet. Maximum operating Pressure 40 Bar, 580 PSI ; Flow Rate - 70 l/min, 18 USGPM, Maximum Temperature - 80deg.C Ideal gun for transfer of many types of chemicals or for caustic washdown. |
|
| |
| New washdown nozzles - chromed brass or 316 stainless steel body, completely covered with 2 anatomically designed shockproof plastic housings fitted with 3 shock absorbing, non marking, rubber rings. Ideal for use with hot water as there are no exposed metal parts and trigger is plastic and protected. |
| 
| Ergonomic - Low Flow
Chromed Brass Body, 1/2" BSPF inlet,
Flow rate 60 l/min @ 20 bar.;
Max. pressure rating 24 bar (350 PSI)
Temperature Rating - 90deg.C
Part No. TEC6400T8L – no swivel
Part No. TEC6425T8SL – swivel inlet
|
|
| 
| Ergonomic - High Flow Chromed Brass Body, 1/2" BSPF inlet,
Flow rate 100 l/min @ 18 bar.;
Max. pressure rating 24 bar (350 PSI)
Temperature Rating - 90deg.C
Part No. TEC6440T8H – no swivel
Part No. TEC6445T8SH – swivel inlet
|
|
| 
| Ergonomic - Low Flow – 316 S/S Body 316 Stainless Steel Body and wetted parts, ,
Flow rate 60 l/min @ 20 bar.;
Max. pressure rating 24 bar (350 PSI), Temp rating -90 deg C
Connection : 1/2"BSPT (F) inlet, |
|
 | Ergonomic - 1/2” BSP Outlet Chromed Brass Body, 1/2" BSPF inlet and outlet,
Flow rate 100 l/min @ 18 bar.;
Max. pressure rating 24 bar (350 PSI)
Temperature Rating - 90deg.C
Part No. TEC6450T8H – no swivel
Part No. TEC6453T8SH – swivel inlet Stainless Steel Lances of various lengths are available for this gun. |
copied from http://www.sulit.com.ph/index.php/view+classifieds/id/1553209/Fire+Protection%2C+Rig+Cooling%2C+Gas+Mitigation%2C+Cooling+Tower+%26+Oil+Burner+Nozzles
Discussion RSS Feeds ] 
Secured Login Option (https)
